These strips are used to mold protective finger coverings or finger splints. These 18’’ long aluminum strips can be bent, cut and shaped as needed. Padded with 1/4’’ latex foam. Box of 12.
The Finger Flexion Glove promotes grasp by providing dynamic traction to the MP, PIP and DIP joints. Made of lightweight, soft, stretchable nylon. Every finger has a metal eyelet built into the tip where dynamic elastic band is fastened.
Each tip’s elastic band has a hook extension piece that easily fastens onto the glove’s 2" (5cm) wide loop wrist strap with D-ring closure. Move this hook piece proximately on the wrist strap to promote greater finger flexion.
To size, measure palm width at MP joints. .Small/Medium 2-1/2" to 3-1/2" (6,4 to 8,9 cm) .Large/X-Large 3-1/2" to 4-1/2" (8,9 to 11 cm)
Provides proper alignment of the MC joints. Can be used with a wrist brace for added support. Neoloop straps secure easily with hook and loop closures.
Oval-8 Finger Splints stabilize and align finger IP joints to enhance hand function. With a simple turn of the splint, each Oval-8 Finger Splint can be used to correct swan neck, boutonnière and mallet deformities, reduce lateral deviation and rest trigger finger. They feature a wide, flat band for comfortable pressure distribution and control.
Made of 1/16" (16mm), high-temperature polypropylene. Oval-8 splints can be adjusted with a heat gun for a small angle alteration.
Available in 14 sizes, each Oval-8 finger splint fits both a full and a half ring size. Sizes correspond to jeweler’s ring sizes, though correlation may vary due to swelling or joint changes. See sizing guide.
The simple, elegant design of Oval-8 Finger Splints allows them to be worn to treat a number of conditions including: Arthritis, Mallet Finger, Jammed Fingers, Fractures, Jammed Fingers, Swan Neck deformity, Hypermobility, Boutonniere Deformity,Trigger Finger. Oval-8 Finger Splints can be worn six different ways, depending on the condition or treatment. Made of seamless molded plastic, the splints are so light and comfortable they are hardly noticeable to the wearer.
The set includes 44 splints in sizes 2 through 15, carrying case, pen light and instructions. Packaged with most splints in the more commonly used mid-range sizes.
Provides constant force to help correct finger flexion contractures of the PIP joint.
ERP5574
$82.45
Provides constant force to help correct finger flexion contractures of the PIP joint.
Easy-to-use finger extension splint. Simply turn and move the positioning nuts on both threaded rods toward the tips for increased extension. Adjusts from 90° PIP flexion to 0° extension. Threaded rod can be cut down using heavy-duty wire cutter.
The finger trough slides along the two parallel threaded rods as the amount of PIP extension increases.
DIP joint is held in full extension or slight flexion depending upon the distal strap placement.
The finger trough and MP pad are constructed of thin, pliable plastic with a soft foam liner.
The trough length can be trimmed with scissors as needed.
Hook and loop fastener straps make adjustments easy.
Oval-8 Finger Splints stabilize and align finger IP joints to enhance hand function. 5 per package.
ERP5575
$65.95
Oval-8 Finger Splints stabilize and align finger IP joints to enhance hand function. With a simple turn of the splint, each Oval-8 Finger Splint can be used to correct swan neck, boutonnière and mallet deformities, reduce lateral deviation and rest trigger finger. They feature a wide, flat band for comfortable pressure distribution and control.
Made of 1/16" (16mm), high-temperature polypropylene. Oval-8 splints can be adjusted with a heat gun for a small angle alteration.
Available in 14 sizes, each Oval-8 finger splint fits both a full and a half ring size. Sizes correspond to jeweler’s ring sizes, though correlation may vary due to swelling or joint changes.
Used for mallet finger and in case of fingertip or nail bed injuries. Reduces the risk of skin maceration. Protects distal phalanx and extends the DIP joint. Latex-Free.
To size, measure the circumference at the DIP joint. If between sizes, choose the larger size.
Ideal for limiting radial and lateral deviation of the PIP joint while allowing active PIP flexion and extension.
ERP5579
$86.45
Wraparound finger pieces are made of a firm, yet moldable, metal frame that is padded for comfort with hook and loop straps. Use to maintain alignment and provide support for PIP injuries due to sprains, strains, partial collateral ligament tears or for post-operative conditions.
Align the hinge to the axis of the joint for proper positioning. If dynamic flexion is desired, add rubber band tension volarly between the two-finger supports.
To size, measure Length from MP to DIP. If in between sizes, choose smaller.
ERP5579-XS X-Small Less than 1-5/8" (Less than 4 cm) ERP5579-S Small 1-5/8" to 2" (4 to 5 cm) ERP5579-M Medium 2" to 2-1/8" (5 to 5,4 cm) ERP5579-L Large 2-1/8" to 2-1/4" (5,4 to 5,7 cm) ERP5579-XL X-Large 2-1/4" to 2-3/8" (5,7 to 6 cm)
Produces flexion of the PIP or DIP joints of the fingers and/or thumb. It is adjustable by careful bending to produce less tension. Not indicated with swelling.
Size Chart: .A: 3,8 cm .B: 4,4 cm .C: 5,7 cm .D: 7 cm